Original do-it-yourself bird feeder. Simple and original ideas for those who don’t know how to make a bird feeder with their own hands from scrap materials Do-it-yourself outdoor bird feeders

Making your own bird feeder is not difficult. In winter, birds are in great danger; they need to be fed.

This is why people create feeders and help birds survive this cold season.

Feeders can be created using any materials that are found in any home. They do not require financial investments or special knowledge, but only a good attitude towards the environment.

General rules for creating feeders:

• convenience;
• moisture resistance;
• safety (exclude sharp corners);
• walls and corners should not be sharp or prickly;
• fastening not lower than 1.5 m above the ground.

Plywood as a material for a feeder

You can make the drawings yourself, or you can find them on the Internet. When selecting or creating a drawing, take into account the features of the tiles.

If you plan to feed small birds, then plan a small opening so that large birds do not compete with them.

Prepare: plywood, hammer and nails, glue, jigsaw (electric), timber (about 20 by 20 cm) and sandpaper.

• Step 1 Mark the plywood and cut out the parts with a jigsaw. Make the square on the bottom and on the roof 5 cm larger (25x25 cm).

• Step 2 Sand the workpieces.

• Step 3 Cut out posts (up to 30 cm) from the block.

• Step 4 Connect the parts with nails (or glue), attach the posts to the bottom, and attach the sides to the posts.

• Step 5 The roof is attached with self-tapping screws.

Wooden feeder

A reliable and high-quality material for any crafts is wood.

Prepare:

• for racks a block (4.5 by 2 cm);
• for the bottom plywood (square 25 by 25 cm);
• plywood for the roof (35 by 22 - two pieces);
• glue, screws, nails.

Step 1 Frame base – assemble the bottom with the sides. Cut pieces of timber to fit the bottom and connect. Glue the ends with glue and tighten with self-tapping screws. It is recommended to make the sides (two parallel) 5 cm longer than the bottom.

Step 2 Nail the bottom to the base frame.

Step 3 Screw the racks (from 18 to 20 cm) to the inside of the box.

Step 4 Attach two bars at right angles. Secure the joints with another block. You need to make two parts in the form of a right angle.

Step 5 Attach the rafters to the posts using rafters and nail pieces of wood to them for the roof.

Step 6 Glue sticks-perches to the sides (extended).

Feeder made from a milk carton

This type of bird house is often made in kindergartens and primary schools. Prepare: milk/juice carton, scissors, wire, marker and adhesive tape.

• Step 1 Cut holes on two opposite sides of the box.
• Step 2 Glue the edges of the “windows” with adhesive tape.
• Step 3 Punch a hole under the windows and insert a cardboard tube (from the cut holes).
• Step 4 Make holes for the wire in the bent corners.

Feeder made from plastic bottles

• Step 1 Cut holes on both sides of the bottle (leave bridges between them).
• Step 2 Apply adhesive tape to the sides.
• Step 3 Make holes at the bottom for the perch stick.

Feeder made from a five-liter plastic bottle

This type of feeder holds a lot of food, which is very convenient for feeding birds in winter. It is convenient for them to eat inside such a spacious product. You can involve the whole family to create. Prepare: bottles, knife (or stationery knife).

• Step 1 Cut a hole vertically or horizontally, depending on the mounting method.
• Step 2 If the holes are made horizontally, then you need to make two holes on the side (with a knife) and pass twine through them (to tie it up).
• Step 3 Place a small stone on the bottom to avoid falling during strong winds.

Feeder out of the box

You can create a feeder from almost any cardboard box. It is better to choose thick and laminated cardboard so that it will last longer in winter moisture conditions.

Making this feeder is easy because it already has the desired shape, walls, bottom and roof. You just need to cut the holes. Prepare: tape, knife and nylon cord.

• Step 1 Wrap the box with tape.
• Step 2 Cut the side holes.
• Step 3 Attach the fastening cord.
• Step 4 Place pebbles on the bottom.

There is an alternative version of this design. The lid can be glued perpendicularly so that it serves as a stand for food.

Then the side and roof will be from the second part of the box.

This product must also be carefully taped. Next you need to make two small wire hooks and lay them on the “ceiling” (twist and bend). The hooks need to be connected to each other, and now it can be hung on a branch.

Photos of bird feeders

70 step-by-step photos and master classes will teach you how to make wooden bird feeders from logs and boards. You can make vertical ones to hang on a window or pole, as well as in the form of houses and gazebos.

Wooden bird feeders are quite durable. They look beautiful and will allow birds not to starve during the cold season.

Simple DIY wooden bird feeder

Depending on what materials you have, wooden feeders will be made.

To create one like this, take:

• round wooden rods;
• board;
• waterproof glue;
• nails;
• necessary equipment.

The feeder drawing will allow you to create it.

These dimensions are provided in inches. But knowing that there are 2.6 cm in one inch, you can create this product. First you will need to saw off a 20 cm long rectangle from the board. Drill holes, stepping back a little from the corners. These recesses will be at a distance of 2.5 cm from the edges. Sides will need to be attached to the base so that the food does not spill out. Make them from narrow boards. Place two on the edge and two on a wide surface.

Now you need to saw the wooden rod into pieces 24 cm long. Attach them to the previously created recesses. From above, these rods need to be fixed to the roof. It consists of two boards that are located at an angle of 90 degrees to each other. Tie a thick rope and use it to secure the wooden feeder at a height.

Sprinkle some treats for the birds, they will be happy to fly here.

Wooden bird feeder in the shape of a house

This one has an opening roof. But you can make it cohesive. First, make a bottom tray, which will also become the floor, and on it you will lay out treats for your feathered friends. To do this, attach 4 edges around the perimeter to the plywood.

Now take the bars and assemble two walls from them, as in the photo.

Attach these two sides to the base of the wooden feeder.

From above, fix the walls in this position using two small bars.

Taking a special or regular ruler, draw an angle on the board. Saw it off and attach such a gable to the top of the feeder, where the roof will be.

Determine where the hinges will be. Attach them to wooden boards.

Pre-drill holes in the gables to thread strong rope through, as shown in the photo.

Secure it so that similar wooden feeders hang securely on a hill.

To make such a cute birdhouse, take:

• processed wooden board 14 cm wide;
• nails or screws;
• hook;
• rope;
• tools.

First, saw off 18 cm from the board. This rectangle will become the floor. You will need to attach 2 parts with pediments to it. To do this, you need to cut 2 boards 20 cm long and sharpen their upper parts at an angle of 45 degrees.

Fix these walls with gables on both sides of the floor. Additionally, secure with boards 13 cm wide. Make a gable roof from two rectangles of boards 20 cm long. The roof should protrude slightly beyond the wall so that precipitation does not penetrate inside and raindrops flow out. Using a hook, secure a rope to hang such a beautiful wooden bird feeder in the shape of a house.

If you want the lid of this device to open, then attach these elements using hinges.

This bird house is attached using 2 hooks. You can make round windows on the sides to be able to observe the birds from all sides. The following diagram of the feeder will allow you to make it perfectly level. But the calculations are given in inches.

The dimensions for the following bird house are also given in inches.

Let's do a little math, you will multiply the presented numbers by 2.6 cm. For convenience, the result can be rounded. Then you will need to cut the boards from which you will make the base, two gable sides and two narrow walls. You will also need a couple of boards for the roof. Using fasteners, secure the rope, the edges of which are placed in the holes in the wall.

The following diagram of the feeder will allow you to arrange all the parts correctly and determine the size of this product.

• See also how to do

Wooden bird feeder with dispenser - step by step photos

This will allow you to always see how much food is inside. It will not get wet and will nourish the birds for a long time. Assemble a feeder that consists of a base and a roof. You need to attach rounded wooden rods to the base by inserting them into the recesses made. Then the birds will be able to sit on these perches and rest comfortably. Connect the roof elements together and attach them to two triangular gables. Make two holes at the top of 1 and 2 halves of the roof. The same ones need to be done at the bottom of the base.

Cut four rounded notches in the center. Take a jar with a tin screw cap. Make holes in the lid. Pour food into the container, screw on the lid and place it in the middle of the floor. When the supply of food in these recesses runs out, it will be automatically replenished from the jar, and the birds will not remain hungry.

You can place a plastic bottle inside a wooden feeder. To do this, you will need to make a recess in the roof, after pouring the food into the bottle, tighten the cap.

Beautiful wooden houses for birds - master class and photos

You will be able to see how much food is left and admire the birds without disturbing their peace.

Look at the diagram of a wooden feeder.

As you can see, the birdhouse consists of a base, two sides, a pair of side walls, a gable roof and a ridge for it. Sheets of transparent plastic are placed vertically on the sides. They need to be fixed so that there is a small gap at the bottom. Then you can pour food inside, and it will automatically pour out into the space accessible to the birds. But make the roof open so you can replenish food supplies for the birds through the top.

You can make this feeder with a dispenser to look like a cabin on the ocean. To do this, construct a roof from large and small branches.

Place large branches at the bottom so that birds can sit comfortably and take food from a plastic container.

• Read also,

Decorative elements for a wooden feeder

These are the words that can be used to describe other bird houses.

This wooden feeder doesn’t even require wood. After all, it is located on the counter. In addition to this bird canteen, there are two boxes in which you can plant greenery or flowers. Take a block of wood for the main post and secure its lower end in two perpendicular boards. To do this, you need to make a recess in the center of 1 and 2 boards and compare them. But first make through holes in the middle of each one the diameter of the block. Now connect this lower part of the feeder using self-tapping screws. Look at how the roof is constructed.

As you can see, it is parallel to the feeder itself. To secure some of the pieces of this bird canteen to a wooden beam, you need to drill holes in them, as well as in the timber. Place the edgings on the glue, inserting them into the holes made.

The elements that you will attach to the edges must be secured using clamps. Hold them until the glue dries.

Once the stand is done, all that remains is to paint it. Fill wooden boxes with soil and plant flowers there.

The next wooden feeder is fixed on a tripod, and the house is made in the form of an open gazebo. Down, food spills out onto the floor. Birds fly here and feast on it.

The next wooden feeder is also an item for decorating the area.

From two small planks, make a cross on which the timber will be attached.

Install it in the holes made and secure it with small oblique blocks.

Cut out 2 oval pieces and make 3 holes in one.

You can insert containers into the holes into which you will pour bird food.

Fasten together a solid oval part and with holes. Place food containers on top. They must have a mechanism that allows the birds to retrieve food.

If you know how to cut wood, then use a jigsaw to make shaped edges for the next structure. This will also be a wonderful decorative element.

Hanging wooden bird feeders

If you need to quickly make a wooden bird house, then the following ideas will help.

For this you will need the following:

• four wooden planks;
• aluminum screen;
• nails;
• hammer;
• metal strips;
• wood glue;
• tools.

You need an aluminum screen in the shape of a square with sides of 25 cm. Take 4 planks and glue them together. Also additionally secure them at the corners with nails.

Use nails to attach the metal strips over the screen. They need to be placed end to end to form a box. Drill holes in the corners of this device where you will attach the hooks. Attach a chain to each using pliers, fix the upper ends on a large link, and then hang this device.

If you wish, make a similar feeder, but paint it white. This one looks especially beautiful against a green background.

To do this, you also need to knock together four boards, placing them on edge to form a box. You can use an aluminum screen or a sheet of plywood as the bottom. Secure any of these materials with self-tapping screws. Then attach beauty hooks to the sides so that the birds can rest here. Insert fasteners into the drilled holes and hang a chain to secure the feeder in an upright position.

And if several birds flock to you at once, then the next hanging feeder will do.

Use round plywood as a base. If you don't have one, cut one out of a square sheet or use a whole square one. Drill four holes on this tabletop so that the fixture will then hang level. Make 4 drawers from the boards or use ready-made ones. Attach a plastic bowl to the center. All that remains is to paint the tabletop, attach the rope and hang the device.

• see also

Do-it-yourself vertical bird feeders - master class and photos

These will save space and use vertical rather than horizontal space.

For such a device, take one and a half meters of boards 15 cm wide and a stainless wire mesh. First, saw the board so that you get 3 sides of 20 cm each. These will be the two lower side edges. The top one should be a little larger so that it protrudes from the right and left. Cut two rectangles of wire to size, insert each into grooves made in advance on the sides and bottom.

Attach a semicircle of wood to the bottom using nails and glue.

Drill holes at the top of the feeder and insert a bent brass rod here. It also needs to be secured to the upper sides of the product.

The following vertical bird feeder will allow them to rest and feast at the same time. These are especially loved by nuthatches and tits, which perfectly hold on to vertical supports.

Take:

• rectangle board measuring 25 by 23 cm;
• rounded perches;
• chain;
• hooks;
• tablet;
• wood glue

The prepared board needs to be sharpened at the top, then several indentations are made in it.

You will do them using a drill of the required diameter. Some holes should be the size of the poles. You will place them on glue and fix them in the recesses. Now you need to mix the birdseed with a small amount of peanut butter to make a viscous mass, and place this treat in the made recesses. Now you can enjoy watching how the titmice appreciate your efforts.

The next vertical feeder is attached directly to the wall or fence.

Take:

• wooden board;
• hot glue;
• nails with a hammer;
• plastic bowl;
• a wooden stick rounded on the sides.

First, it is better to cut out the parts on cardboard or paper in order to be able to compare them and make adjustments to these templates.

In the board that will be the floor, drill a hole in the side center to pour glue here and fix the wooden perch. Now knock down the roof elements, attach them to the wall, and attach the floor. You also need to glue the plastic container so that it does not get blown away by the wind and birds do not accidentally drop it. When the glue dries, it’s time to pour food inside the container and wait for guests.

This next vertical feeder is also quite nice. You need to use nails and glue to connect the gable roof to the walls, and them to the floor. Attach a treated rounded wooden board with holes in it at the back. Use these to hang a chain or rope to secure this bird canteen. You can draw or glue their images, then such wooden feeders will look even more interesting.

The vertical one can also be attached to the window using a suction cup. Then, while at home, you will be able to watch how the birds fly to you to feast on food.

To set up this bird canteen you will need these suction cups with fasteners. On the one hand, they will be fixed on the window, and on the other hand, you can fix them on a wooden plank using self-tapping screws. Knock down a wooden box. To do this, the floorboard must be level, and make a bevel at the top of each sidewall by sawing one board in this way.

Now you can attach the sloping roof on top; it will be located on a strip that is fixed to the two upper parts of the sidewalls. Cut holes here in advance to secure the two upper suction cups. Now you can fix the roof and attach the feeder to the window.

You can make it open. To do this, knock down a box, make a bottom out of plywood or aluminum sheet or plastic mesh. Fix this device on two vertical bars. Attach suction cups to it, or you can fix hooks on top and hang it on the window.

You can also attach a horizontal feeder near the window, securing it with chains. To ensure that the birds have a varied menu, stuff slats between the parts of the bottom to separate the dishes.

And if you use transparent plastic, then you will pour food between its two sheets, make a hole at the bottom so that the food pours out here in doses. Then you can watch the birds, and they watch you.

The next wooden feeder, made with your own hands, is also very interesting. The side bars and walls are attached using metal corners. This feeder is attached to the wall using special fasteners. Its walls are plastic, they are not closed on the sides, so that food can be poured through these holes, and the birds can flock to the treat.

You can fix the next bird feeder on a wooden window frame from the outside or on a block placed vertically.

First you will need to cut 8 boards of the same size. Make an octagon out of them by attaching them as follows.

Attach one board from one opposite side to the other, attach two more perpendicular to it, so that you get a cross like this inside. Attach the bottom using wooden sticks or plywood. Take a strong narrow board and attach two wooden fragments cut at an angle to its ends. Using one you will attach this leg to the bottom of the feeder, and the second will help secure this bird's dining room to a vertical wooden support.

DIY log bird feeder - step by step photos

Such wooden feeders also look very interesting and will be useful for birds.

This bird's canteen looks natural. It seems as if the titmouse is simply jumping on a log in search of food, but in fact the product was made from a log.

To do this, you need to cut off an element of the required size from the log, hollow out the wood inside, leaving impressive side walls. Attach hooks at the top and bottom for fastening. Now you need to put food here, but regular food will spill out, so do it as follows. Take coconut or peanut butter and melt it on low heat. Then mix the peanuts with other grains. Place the resulting food into the hole of the log, press with a spoon so that the treat fits tightly into the container.

Now pour a small amount of prepared melted butter on top and let the structure harden. When this happens, use hooks to hang this wooden feeder in place.

The birds will surely appreciate your efforts. If you have small logs or twigs, use them to make a roof for your next feeder.

To do this, you need to saw the logs in half lengthwise and make a roof out of them, attaching them on the back side at the top and bottom along the plank. Fix 2 planks on the created base, they will become vertical walls. Attach the structure to a log dug vertically into the ground.

If you do not have suitable boards, but only thick branches or thin logs, then make the basis for a bird's dining room from them.

Attach a sheet of iron or polycarbonate on top, and at the bottom attach this structure to a rectangle of plywood.

If there is a log, then use special tools to remove the middle from it, place this structure on its side and hang it. You will get a wonderful house for birds, into which you will pour food for them.

The next one is also quite easy to do. If you do not have oval blanks, then you can cut the handle from a rake or shovel, and also take bars.

• Article

From this article you can learn how to make bird feeders with your own hands: an overview of existing types of structures and general recommendations for their creation and placement, selection of suitable building materials, photos and drawings with a detailed description of the technology. The text contains unusual and original solutions that will allow you to create a comfortable and beautiful area for feeding birds in the garden or near the house.

Wood is the most common material for making feeders

If they want to improve the area near their house, many owners of summer cottages lay paved paths, lay out flower beds and flower beds, install benches and lanterns. All this creates comfort and coziness for the residents of the house. However, we should not forget about the small inhabitants of the garden, for whom, with the arrival of winter, it becomes more difficult to obtain food for themselves.

Creative feeder made from a saucer and cup

Making a bird feeder with your own hands will not only help birds overcome this difficult period, but will also add a certain charm to the garden. Using simple technologies, you can show your own imagination and create an original feeding house.

Advantages of homemade feeders:

• the opportunity to take care of birds that find it difficult to obtain their own food;
• decorative decoration of the yard;
• an opportunity to instill in children a love of the environment and birds.

You can easily make a wire fruit feeder with your own hands

Moreover, such a decision can be implemented not only by owners of private and country houses, but also by residents of city apartments.

Is it profitable to buy a ready-made bird feeder: advantages and disadvantages

If you want to install a standard professionally made feeder in your yard, you can order the product from specialists. Experienced craftsmen will independently select high-quality materials and make the structure using special technologies.

Finished plastic bird feeder

Buyers are invited to choose a bird feeder with a design they like based on the picture. Such structures can have any size and shape. By purchasing a custom-made feeder, the consumer can be completely sure that it will meet his wishes and fit perfectly into the exterior of the yard.

Purchasing finished products comes with both advantages and disadvantages. The negative aspects of this include the high cost of professionally made feeders. In addition, the buyer deprives himself of the joys of the creative process and waiting for the birds to arrive. Therefore, many people prefer to create their own houses for feeding birds in their yard or near a window.

Hopper type feeder for feeding two birds at the same time

Note! The design of the feeder must be reliable, so it is advisable to select practical and durable materials for its construction that will protect the birds from precipitation and wind.

What requirements must a homemade bird feeder meet?

When choosing a specific design for a homemade feeder, you need to take into account not only the type of birds for which the design will be made, but also other nuances. Birds mainly rely on their vision, so the poured food should be visible to them from afar.

Original feeders using wine bottles

The design of the structure must be such that the grain is not covered with snow or blown by the wind. High sides and a roof will help to cope with this problem. It is unacceptable for moisture to get on the feed. Otherwise, the grains will become moldy and spoiled. It is desirable that there is protection from chipmunks and squirrels. In this case, the birds should not experience any difficulties when removing food.

Drawings of bird feeders, of which there are many on the Internet, can be successfully used as a visual aid for creating a beautiful design. First of all, you should pay attention to practical and convenient options. The food should not spill onto the ground, otherwise it will attract small predators such as stoats, weasels, and ferrets. Their presence poses a direct threat to birds.

Bird feeder is made in the form of a mesh flower

If the structure will be used for temporary feeding in winter, it is better to hang it. Thus, the feeder will attract less sparrows, which find food much easier than other birds. Stationary structures are used for constant feeding. In this case, protection from predators is mandatory. It is desirable that the grain is located on a level area of ​​sufficiently large size that maintains good stability.

Types of bird feeders: photos and descriptions of designs

The design of homemade feeders is practically unlimited. The main thing is that the design meets the basic requirements of practicality, reliability and safety.

Waffle cups were used to create grain hangers

Classification of bird feeders by type of design:

• suspension;
• area;
• house;
• bunker;
• tray;
• peeler

Each of these designs has its own characteristics and is designed for certain types of birds.

The bird feeder can be cast from plaster or clay

Original do-it-yourself bird feeders: photos of hanging structures

The designs of the suspensions are very simple. In this case, the food is suspended in a mesh case or on a thread. They are used primarily as tit feeders. Although other species of insectivorous birds, with the exception of woodpeckers, can also use dewlaps.

The most common version of “antifreeze” feeding is a piece of lard without spices and salt. There are also more nutritious mixtures that are designed for shelling birds. A ball made of seeds is suitable for them. Peanut oil or lard (gutter fat) is used as a binding component.

Beautiful examples of hanging bird feeders

Note! You should not cast the feed mass into a beautiful mold or plastic cup and then freeze it. The ball is more comfortable for birds. This makes it much easier for them to cling and they don’t have to expend a lot of energy to keep themselves afloat while feeding.

It is most convenient to form a ball consisting of feed mass with your hands. This must be done in the cold. The fat will harden very quickly, so after forming a ball, you need to hang it up immediately.

Related article:

Aviary for dogs: photos of successful DIY designs

Drawings, interesting and practical solutions for creating fences in street and apartment conditions, taking into account the breed and size of the animal.

Hanging bird feeder crafts can be made with specific types of birds in mind. Great tits prefer garlands made from dried berries. They especially like rose hips. Peanuts in pods are allowed.

Original wicker basket with nuts for birds

The best option for blue tits would be swing feeders. In this case, it is advisable to hang the balls on elastic and thin branches so that they balance.

The beautiful do-it-yourself bird feeders, made in the form of mobiles or movable sculptures, look original in the photo. Such designs can even attract great tits, which will not conflict with blue tits.

You can use a regular plate secured with chains as a feeder.

Hanging options made from cones are suitable for attracting bullfinches, shelling birds and waxwings. To make the feeder visible from afar, you can hang a bright bunch of rowan or viburnum on it. It is advisable to use a fertile cone for this. If this is not possible, any with ruffled scales will do. It needs to be doused with peanut butter. After this, food is placed between the scales and the cone can be hung. Even crossbills may like such cones.

You cannot use paper to create such structures, but you can make a beautiful bird feeder with your own hands from a thick base from a toilet paper roll. It is advisable to attach bright pieces of fabric or paper from below that will attract the attention of birds.

Creative coconut shell feeder

Convenient DIY bird feeders: photos of tray structures and platforms

Platform feeders are a flat surface on which food is placed. The advantage of such designs is that birds can see the presence of food from afar. However, there are some disadvantages to a DIY flat wooden bird feeder. Firstly, there are no fences to provide protection from the wind. As a result, large quantities of food swell and fall down. Secondly, nothing prevents sparrows from actively using these feeders.

The fact is that sparrows live in flocks. These nosy birds, unlike pigeons and crows, can freely penetrate small feeders and empty them, not giving a chance to other birds, for whom it is much more difficult to obtain food in winter. To eliminate this possibility, it is advisable to avoid the use of open structures.

An easy way to make a bird canteen is to use a wicker basket.

Sparrows are very careful. In case of danger, they take off straight from their place steeply. Therefore, the best option would be a birdhouse made of cardboard or wood with a steep roof that has more overhang. It is desirable that the structure have low windows to provide birds with access to food. In this case, the sparrows will first have to flutter to the side before flying away, so such feeders are unattractive to them.

Helpful advice! In winter, birds could use a vitamin supplement. To do this, you can put pear and apple cores with seeds, viburnum berries, elderberries, rowan berries, the fibrous part of a pumpkin with seeds, dried rose hips, and grape seeds in the feeder. You can use cherry pits from compote.

Feeder-platform made of wood on a long leg

For those birds that constantly live on the site, a home-made original tray-type bird feeder is suitable. In front of the tray (window that provides access to food), you can install a perch or landing pad.

There are two types of tray feeders:

1. With free access to the mixture.
2. With automatic feeding of food into the tray.

The bird tray can accommodate grain and fruit food

A window bird feeder with automatic feeding is much more practical than bunker structures. In this case, the food practically does not wake up. Trough structures are designed specifically for one type of bird. It is possible to use a feeder for several species of birds. However, creating such a structure will require not only appropriate skills and tools, but also ornithological knowledge.

DIY birdhouses: photos of birdhouses and similar structures

Feeders in the form of houses protect food well from snow. By equipping the structure with a roof, you can protect the inside from the wind and sparrows. But a beautiful bird feeder in the shape of a house does not provide protection against food spillage. Therefore, only those birds that are accustomed to feeding will be present on the site. For forest birds, this option is very inconvenient, because they are drawn to human habitation only in cases of crisis and may simply not notice grains that have spilled onto the ground.

Simple wooden feeder house

A structure in the form of a house with a sloping roof can be made from a box. If possible, it is advisable to treat such a cardboard feeder with a diluted adhesive composition. For this purpose, PVA is suitable, which is mixed with water in a ratio of 1:3 or 1:5. The supports are made of sticks, which are also attached with glue. If everything is done correctly, such a feeder will last for several seasons. The structure is nailed to the tree.

A beautiful feeder with a pitched roof will be the best option for strong, large birds. These include nutcrackers, waxwings, jays and pigeons. All of them can sit quietly in a row during feeding, so it is better to equip the dining room with a long perch.

The dining house is complemented by a hanging bag of treats

Wood or very thick pre-treated cardboard can be used as a manufacturing material. The design for large birds should be much larger than for ordinary birds. In this case, you need to select bird feeder drawings with dimensions that will suit them.

Note! A shoebox bird feeder is not suitable for feeding large birds. The cardboard in such designs is very thin. Strong birds will very quickly break the feeder while feeding.

Bright elements on the feeder will attract the attention of birds

Practical do-it-yourself feeders: photos of bunker structures and shellers

Bunker-type structures are the best option if an anti-sparrow feeder is required. In this case, the feeding area is limited in size, so the entire flock cannot accommodate. The sparrows will have no choice but to eat alternately with the company of other birds.

Unusual bunker-type bird feeders can have different designs. It is advisable that a product designed for small spotted woodpeckers and tits be equipped with a hard, narrow platform. Anti-sparrow versions are much wider and have a roof. Modern materials make it possible to create a bunker structure in just 5 minutes.

To make a feeder, you can use glass vessels - vases, small aquariums, flower pots

To make your own bottle feeder you will need a minimum set of tools and materials:

• nylon thread;
• bottle (PET);
• Super glue;
• plastic plate;
• large needle;
• knife and scissors.

Plastic is a very practical and durable material that is not afraid of moisture and frost. This feeder will last for several seasons.

Hopper type feeder can hold a large supply of bird food

Shelling feeders are less popular. They are designed for a specific type of bird. In this case, the feed is retained using a special metal mesh. The design can be improved by making it combined. For this purpose, the peeling feeder is combined with the tray version. Thanks to this, birds of different species can coexist in one area.

How to make bird feeders: choosing materials for work

Having decided on the type of future design, you need to decide what the feeder will be made of. A variety of materials can be used for these purposes. Everyone has many of them in their home, so you can not only create an original bird feeder with your own hands, but also do it at minimal cost.

To make a feeder from a coffee set, you need to glue the cup to the saucer and secure the structure to the handle

The following materials are usually used to make poultry canteen:

• plastic;
• paper and cardboard;
• wood;
• plywood;
• improvised materials (bottles, boxes, milk or juice bags, etc.).

Each of the listed materials is suitable for creating certain types of structures and has both advantages and disadvantages.

Simple feeders can be made from cardboard cups

Features of bird feeders made from plastic bottles and trays

Plastic feeders are the most popular option. This material has many advantages.

Advantages of feeders made of plastic bottles and trays:

1. Availability of material.
2. The transparent walls of the structure make the food visible from afar.
3. Ease of processing.
4. Minimum amount of garbage and waste.
5. There is no need to use special tools.
6. High strength and durability.

An affordable and simple way to build a feeder is to use a plastic bottle

Important! The roof of a plastic feeder in the form of a house should be opaque or at least matte. In case of danger, birds may not notice the transparent plane above and hit it.

A good way to create a small, visible bird feeder from scrap materials is to use old children's toys, such as blocks. They are made of polyethylene, so it is advisable to use superglue for fixation. Such designs have bright and rich colors, so it will be easy for birds to find food. Polyethylene is easy to process. To cut round holes in the walls, you can use a compass with two needles. Polyethylene is a slippery material, so it is advisable to equip the feeder with a perch.

Bird canteen made from a plastic bottle and a wooden spoon

As a plastic building material, you can use scraps of transparent polycarbonate that may have remained after renovations in the house. This feeder can be mounted on a window using suction cups from bathroom shelves.

Bird feeders made from bottles and other unsuitable containers deserve special attention. The main thing is that the design is well thought out. To ensure visibility of the feed, it is advisable to use a wide tray. The presence of a perch will make feeding birds more convenient. If you take a large tray and a capacious container, you will not have to frequently replenish food supplies. As a result, the birds will be less timid.

The design of the feeder is made of a plate and a bottle

To make a bird feeder with your own hands from a plastic bottle, it is advisable to use a trough-shaped tray. In this case, spillage of feed will be insignificant. If you bend up the lid of the hatch that provides access to the food, the feeder will turn out to be anti-passerine. In this case, the plane that is formed at the top can be used to place vitamin supplements.

Features of making homemade feeders from a box

• milk;
• kefir;
• juice, etc.

A simple and original bird feeder made from juice tetra pack

Despite the fact that these bags are made of cardboard, their walls are covered with film on both sides. Therefore, laminated feeders can withstand one winter.

Small bags left over from juice or milk are ideal as feeders for the following types of birds:

• goldfinches;
• tits;
• granivores.

Feeding houses made from cardboard milk bags

In this case, you must install a perch stick to make it easier for the birds to get food.

Helpful advice! To attract the Great Spotted Woodpecker to the tit feeder, just attach a wooden circle to the bottom of the valve. This will make it easier for the bird to attach itself to the structure.

Feeders made from juice boxes

Large bags can be used to make universal bird feeders. To do this, you need to cut a large opening so that the food can be seen from afar. If the feeder is hanging, it needs to be pierced with a perch. The structure from the package can be placed in a bush. In this case, a perch will not be required; its function will be performed by the branches.

Eco-friendly do-it-yourself bird feeders made of wood

The advantage of wooden feeders is their durability. Most often, such structures are stationary.

Wooden feeder-dining room, made in a modern design

As a protective treatment you can use:

• drying oil;
• water-polymer composition;
• mixture in the form of diluted PVA glue.

To build a bird feeder out of wood with your own hands, you will definitely need carpentry tools and skills in handling them. Traditional models look like a house. It is not recommended to put a flat roof on the feeder, as this will expose the food to weathering.

Bird feeder made of logs

Standard house-shaped designs can be improved and specialized for a specific type of bird through minor changes. For example, a feeder with a gable roof without railings can be used as a public option. If you build a small sheathing around the perimeter, such a dining room will appeal to shelling birds. It quite realistically imitates natural feeding conditions. A similar model with a continuous low fence will achieve an anti-sparrow effect and protect food from the wind.

A design in which the roof has low slopes will also provide protection against swelling of the feed. Such a feeder will be used by sparrows only as a last resort.

Original swing feeders for birds

An alternative to a suspended wood structure would be a DIY bird feeder made of plywood. To create it, you will also need wooden blocks with a section size of 3x3 or 3x4 cm. To avoid the use of lumber, you can make bars from strips of plywood by gluing. However, for stationary feeders on poles, it is preferable to use solid wood, since plywood in outdoor conditions will delaminate after a few seasons, regardless of the quality of the protective impregnation.

Helpful advice! If you use waterproof birch sheets to build a bird feeder from plywood, you can get a reliable and durable structure. This material perfectly withstands outdoor conditions.

Birdhouse made from cork plugs

DIY bird feeders from scrap materials

Unusual and original designs can be made from scrap materials, the creation of which can focus on design or functional features.

An ear of corn can be used as a feeder. To do this, a nail is passed through it. This version of a bird feeder made from scrap materials can simply be hung or made part of a stationary structure. Corn should be firm, preferably oilseed or fodder varieties. The smaller the grains, the better.

Simple Egg Tray Bird Feeder Design

It is better to avoid using table sugar cobs, as they are harmful to birds. Their grains contain large amounts of sugar and starch. The corn feeder is designed for large frugivorous and granivorous birds, as well as shellers.

You can use Popsicle sticks as a building material to create a wooden bird feeder. During the summer season they can be accumulated in sufficient quantities. To make such a structure you will need string and PVA glue. You can install a pole of larger popsicle sticks on each side of the feeder. Thanks to this, the dining room can be used by 4 birds at the same time, for example, chickadees or siskins.

Original feeder-holder for food from a kitchen whisk

An excellent option would be a wicker basket-shaped feeder with a hanging lid. To create it you will need paper tubes, which can be made from old newspapers. The weaving technology is quite complex and labor-intensive, so not everyone will decide to take on the construction of such a feeder, but the result exceeds all expectations. To prevent paper straws from becoming soggy, they need to be treated with a protective compound (glue and stain).

A large metal tin can is also suitable for constructing a feeder. It is suspended on a rope in a horizontal position. To prevent food from spilling onto the ground, you need to install a small damper. The top part of the lid, bent in half, is suitable for this. You definitely need to install a perch.

The bird's dining room is made from a small tin can

Important! Regardless of the type of design, the feeder must be safe. Wooden models must be thoroughly sanded and all sharp corners must be rounded. Metal options can be wrapped with twine, which sits on the glue.

Making bird feeders: drawings, descriptions and technologies

Having decided on the type of design and material, you can begin the actual manufacture of the feeder. It is worth noting that not all types of grains are suitable for feeding birds. The favorite food of birds that stay for the winter are seeds of wild grasses. It is desirable that these are burdock plant species. A turnip seed is suitable, which can be collected in the summer or purchased ready-made at a pet store.

Forged fruit holder for vitamin feeding of birds

Homemade feeders can be filled with:

• oats and millet;
• small sunflower seeds (unroasted);
• hemp and flax seeds;
• dried pods of acacias that live in mid-latitudes (wisteria, honey locust, sophora, etc.);
• pumpkin seeds;
• dry pea pods (they must be ripe and firm);
• pine nuts;
• millet (in small doses);
• seeds of deciduous trees such as ash, hornbeam, linden, maple, alder;
• acorns and seeds of coniferous trees, for example, beech nuts, ruffled cones (if the feeder is designed for shellers).

Drawing of a square wooden bird feeder

Note! The use of rye, wheat and bread is not allowed. They are harmful to birds. Moreover, black bread is the most dangerous because it causes inflammation of the goiter. Porridges that swell greatly during cooking, such as buckwheat, pearl barley, and rice, are poorly received. The peel of any tropical fruits and citrus fruits is lethal to birds.

How to make a birdhouse with your own hands: assembling a wooden structure

To build a wooden birdhouse you will need skills in working with carpentry tools.

Large wooden bird feeder house

For work you will need the following materials:

• wooden beam for racks (2x4.5 cm);
• a square of plywood as flooring on the bottom (25x25 cm);
• wooden pieces for roofing (22x35 cm, 2 pcs.);
• fastening elements (adhesive, screws, nails).

It doesn’t hurt to first find a suitable drawing of the feeder, which will help you navigate when assembling the parts.

Drawing of a wooden feeder: 1 and 2 - roof slopes, 3 and 4 - roof ridge, 5 and 6 - side walls, 7 and 8 - sides

First, the base is assembled: sides and bottom. To do this, the bars, pre-cut according to the size of the bottom, are glued on the end sides and fixed with self-tapping screws. The result is a wooden frame. A pair of sides running parallel should be made longer than the bottom by about 5 cm. They will be used to install perches. The bottom is nailed to the frame using nails.

At the next stage of making a feeder with your own hands, stands are mounted from wood. To do this, you need to screw the corresponding parts on the inside of the box. The optimal length is 18-20 cm.

A wooden feeder will harmoniously fit into the overall appearance of a private yard

The rafter system is attached to the racks. To do this, you need to connect a pair of beams at right angles. To strengthen the place of fixation, the joint is secured with a piece of timber. The result is a right angle with equal sides. According to the drawing, it is necessary to make two such parts.

Helpful advice! To properly connect the parts of a wooden bird feeder when fastening the bars, you need to lay the flat, wide part on the table. After this, an additional element is attached to the top at the appropriate angle.

Technology for making a feeder from ice cream sticks

Then the rafters are attached to the posts using self-tapping screws. Next, the roof slopes are installed. To do this, two wooden elements are installed on the rafters. If you have a wooden corner available, you can make a ridge. A bird feeder made of wood needs a perch. To do this, sticks or window beads are glued between an elongated pair of sides.

This design can be either stationary or suspended. It can be installed on a pole or, by making a couple of holes in the ridge, hung on a wire.

How to make a bird feeder with your own hands from wood: plywood structure

An alternative to a wooden feeder is a structure made of plywood.

The material allows you to choose any modification:

• open;
• with a gable or flat roof;
• with bunker compartment.

Drawing of a plywood feeder: 1 - side wall 2 pcs., 2 - base, 3 - bottom, 4 - roof 2 pcs.

Plywood is a derivative of wood, but it is much cheaper and lighter in weight. Before you make a bird feeder from wood, you must select the appropriate drawing. In this case, you need to take into account the type of birds living in the region. Large birds such as magpies, pigeons and jays can eat all the food, leaving small birds without food. Therefore, if the feeder is designed for tits, the openings should be such that large species cannot reach the grains.

For work you will need the following tools and materials:

• jigsaw;
• sandpaper;

A small simple feeder can be made from leftover building materials

• water-based adhesive composition;
• nails and hammer;
• plywood sheet;
• timber with a section size of 2x2 cm.

In accordance with the drawing, markings are applied to the plywood sheet. After which all the parts are carefully cut out using a jigsaw. A square element of 25x25 cm will be used as a flooring for the bottom. To build the roof, you need to take larger parts, otherwise moisture will drain onto the feed. The edges of the resulting blanks must be sanded.

Drawing of a birdhouse made of plywood

You need to cut 4 posts, each 25-30 cm long, from the timber. If the structure has a pitched (flat) roof, a pair of bars should be shortened by 2-3 cm. The cut is made at an angle. All joints between parts are treated with adhesive and then fastened with nails. The racks are installed on the bottom, and the sides are fixed to them. A roof is installed at the top of the racks. The structure can be installed permanently or suspended using a hook and hardware.

Helpful advice! If a wooden feeder will be opened with varnish, it is recommended to use a water-based composition for this so as not to harm the birds.

Plywood house-dining room for birds

How to make a feeder with your own hands: hanging structure made of grain

Suspended structures made of grain are the simplest option. This design can be made in a few hours.

To work you will need:

• raw bird food;
• oat groats;
• egg;
• gelatin;
• flour;
• needle and thick thread;
• thick cardboard and scissors;
• pencil and molds for filling.

Hanging grain structures not only help feed birds, but also decorate the garden

How to make an edible bird feeder with your own hands:

1. Draw the shape you like on the cardboard, for example, a square, circle, triangle, heart, etc.
2. Cut out the shape according to the markings.
3. Form a fastening by threading a needle and making a hole.
4. Prepare the adhesive mixture. To do this, mix the following ingredients: 1 tsp. honey, egg, 2 tbsp. l. oatmeal and a small amount of flour.
5. Leave the mixture for half an hour.
6. Apply the adhesive mixture over the cardboard base.
7. Mix grain feed with adhesive mass.
8. Apply the resulting mixture onto the cardboard base.

You can make grain hangers using a silicone baking mold.

After this, the grain feeder should be placed in the refrigerator for several hours. Once the mixture has hardened, the products can be hung on tree branches in the yard.

There is another technology for making edible feeders:

1. Dissolve a packet of gelatin in warm water.
2. Pour food into it.
3. Place the resulting mass into molds.
4. Insert thread for hanging.
5. Place the molds in the refrigerator for several hours.

Original hanging feeder made from half an orange

After hardening, the feeders are completely ready for use. To make it easier for birds to grab onto, the molds can be placed in bright mesh bags.

How to make a bird feeder from a plastic bottle

Every home has unnecessary plastic containers. Therefore, many people are thinking about creating a bottle feeder. The material is cut with scissors or a knife, and the design is transparent and very light. This option is especially convenient since there are several ways to create plastic feeders.

Children will also be happy to participate in making a feeder with their own hands.

How to make a feeder from a plastic bottle:

1. A pair of holes are cut out on both sides of the bottle. They should be located symmetrically. The shape can be any: arch, square, circle, rectangle.
2. Spacers must be left between the holes.
3. You can make a rain canopy by making an inverted U-shaped slot and bending the plate upward.
4. The lower edge of the slots where the birds will land must be secured. To do this, the cut is covered with fabric insulating tape or adhesive tape.
5. In the lower part you need to make symmetrical holes.
6. A perch stick is inserted into the resulting holes.

A simple feeder made from a plastic bottle and wooden perches

This feeder can be mounted on a tree. To do this, the jumper is wrapped with rope, tape or other material.

Helpful advice! If you insert twine through the lid of a birdhouse from a bottle, having previously made holes in it, you can form a loop that will allow you to hang the structure on a tree branch.

An original feeder made from two plastic bottles

Do-it-yourself bunker feeder from a plastic bottle

The bunker design is very rational. It allows you to fill up the feed mixture with a supply of several days. As the birds eat the grains, the additive will automatically flow into the tray.

To work, you will need a couple of bottles of the same capacity. Markings are applied to one container using a marker. Near the bottom, you need to make holes similar to those made in the previous version of the plastic feeder, and then remove 1/3 of the bottle (from above).

Scheme for making a feeder from a plastic bottle attached to a tree

A pair of symmetrical holes are made in the upper part. These will be used to hang the feeder using ribbons or twine. The second bottle will contain food. In the narrowest part of this container, several holes should be made through which the grains will spill. Don't make the holes very large. If necessary, it is better to expand them later.

The corresponding bottle must be filled with the feed mixture, screw the cap into it and place it inside the container, which is cut off by 1/3. After this, twine is pulled through the holes and the structure is suspended from the tree.

From the neck of a bottle you can make a hanging feeder from grains with the addition of gelatin

How to make a bottle feeder: a simple design with a spoon

There is another version of the bunker design - a feeder with a spoon. A bottle with a capacity of 1.5-2 liters is suitable for this. First, you need to make a hole in the cork and stretch the twine through it. Using it, the structure will be suspended on a branch. Then you need to make holes symmetrically (one on each side of the bottle). They should be the size of a wooden spoon.

On the side where the deep part of the spoon will be placed, the hole needs to be slightly widened so that it is convenient for the birds to take food. All that remains is to fill the feeder with the selected feed mixture and hang it in a convenient place.

Technology for making a feeder from a plastic bottle and a wooden spoon

Helpful advice! To prevent the bunker feeder from accumulating moisture, several holes need to be made in the bottom. To do this, you can use a small nail or a hot needle.

How to make a bird feeder from a 5 liter bottle

5 liter water bottles can hold much more feed than standard containers. In addition, the large size of the container allows you to make several holes, so that a large number of birds can feed at the same time at the feeder.

5 liter bottle can hold a lot of birdseed, with enough supply for several weeks

To work you will need:

• wire or ribbon for hanging;
• clean bottle;
• birdseed;
• cutting tool, such as pruning shears, scissors or a utility knife.

First, a hole is made for hanging the structure. Its location will depend on the nature of the placement of the feeder on the tree:

1. Horizontally - a pair of wide holes are made (one near the neck, the other from the bottom).
2. Vertically - at a distance of 5-7 cm from the bottom of the bottle, you need to cut 3 rectangular holes or several square ones.

It is advisable to make several openings-doors in a plastic bottle for ease of movement of birds

It is most convenient to hang the bottle by the neck. If the structure will be fixed in a horizontal position, you need to make two holes in the wall and, passing twine through them, fix the feeder to the tree. Plastic structures are very light. To prevent the bottle from being swayed by the wind, it is advisable to place ¼ of a brick at the bottom before pouring food into it.

Technology for creating a bunker feeder from a 5 liter bottle

To create a bunker feeder, you will need several bottles (5 l - 1 pc., 1.5 l - 2 pcs.), as well as a stationery knife, rope and marker. First, markings are applied to large containers. Using a marker, the area near the bottom is marked where the hole will be placed, which will serve as a taphole. It is best to make 2 small slots and one large one through which you can install a 1.5 liter bottle.

Technology for creating a winter bird feeder from a plastic bottle

Then a U-shaped hole is cut upside down. The upper part should be folded back to form a protective canopy against rain. The lower edge of the opening is sealed with adhesive tape so that the birds do not get hurt during feeding.

In those areas where the bottle placed inside comes into contact with the bottom of a large container, as well as in areas slightly higher, you need to make holes. As the food is eaten, the grains will spill out through them. A round hole is made in the cap of a 5 liter bottle so that after screwing the thread, the neck of the inner container rises. Then you need to cut off the neck of the second bottle along with the top. The result should be a funnel. It should be placed on the neck of the inner bottle and screw on the cap. The feeder is ready.

It is better to place the doors in the bottle not at the very bottom, which will ensure a certain supply of food

Helpful advice! It is advisable to install a feeder under the roof to make the birds more comfortable. A canopy or gazebo is suitable for this.

How to make a feeder from a box: process description

A homemade bird feeder can be made from the simplest materials available. Almost every home contains boxes of food, shoes or electrical appliances. For work, it is advisable to select thick cardboard. An ideal option would be a bird feeder out of a box with a laminated coating, which will increase the service life of the structure.

The feeder from the box can be equipped with suction cups and attached to the window glass

The advantage of this method is that the box already has walls, a bottom and a roof. Therefore, the steps to convert it into a feeder will be minimal; you will only need to cut rectangular or square holes on the sides.

To make a bird feeder with your own hands from a box, you will need a utility knife or scissors, cord and tape. Since cardboard is short-lived and vulnerable to moisture, it should be wrapped with tape for protection. This is done after the feeder is ready. When holes are cut in the side walls to access the feed, you need to secure the cord and hang the feeder. To prevent the structure from swaying from the wind, you should put some pebbles or sand on the bottom.

Examples of bird feeders made from shoe boxes

You can change the technology slightly. In this case, the box lid is glued perpendicularly. As a result, it will serve as a stern stand. The second part of the box will replace the roof and fences. The structure must be sealed with tape.

Next you need to organize a mounting system for hanging. To do this, a pair of hooks is made from wire. A piece of wire is bent in half and the end makes a puncture through the “ceiling” part of the feeder. After this, the wire is twisted and bent on the inside. Now the feeder can be hung on a branch.

Technology for making bird feeders from cardboard

How to make a feeder from a juice or milk box

To create such a design, you will need a tetra pack bag for liquid food products, such as juice or milk.

List of necessary materials and tools for work:

• wire for hanging or nylon rope;
• a clean milk or juice carton;
• adhesive plaster;
• stationery knife or scissors;
• marker.

You can make beautiful feeders from juice or milk cartons

The feeder should be comfortable for the birds, so markings are applied to the cardboard and a pair of holes of sufficient size are cut on opposite sides. The through space will allow birds to move and feed easily. For safety reasons, the window should be covered with adhesive tape.

Under the slots you need to pierce a hole with scissors and insert cardboard rolled into a tube into it. This will be a roost. The material for its manufacture can be taken from scraps left over from previous operations. In the corners you need to make small holes where the rope or wire will be stretched for hanging. A milk carton feeder can be tied to a branch or mounted on a tree trunk.

Technology for creating a feeder-house from cardboard tetrapack

Helpful advice! To prevent the structure from swaying, it is better to cut slots not on opposite sides, but on adjacent walls of the bag.

The feeder can be made from two juice packets. The first tetra pack needs to be cut along the narrow side parts so that the top remains intact. 1/3 of the second bag is cut off, and a hole should be cut on the front side. This area will be used as a stern board. The bottom of the second tetra pack must be combined with the first bag. If everything is done correctly, you should end up with a triangle. To fix the parts, it is better to use glue, as well as wrapping with tape.

Bird feeder made from a box, rope and wooden sticks

How to decorate a bird feeder with your own hands: interesting ideas

When the feeder is ready, you can start decorating it. In this case, everything depends solely on imagination. The design of homemade bird canteens is practically unlimited, the main thing is that all decorative elements are environmentally friendly and safe for birds.

How to decorate a feeder using scrap materials:

• paint the structure with a coloring compound;
• decorate with weaving from ropes or twine;
• use materials of natural origin as decoration, for example, moss, tree bark and branches, cones, acorns, chestnuts;
• decoration with colored ropes;
• use of chains with unusually shaped links, etc.

You can decorate the feeder using carved elements

On the Internet you can find many interesting ideas for decorating homemade feeders. If you approach this issue thoroughly, you can make a house of an unusual shape. After that, the paint remaining after the repair, various figures and colored paper are used for decoration. However, you should not overdo it with rustling and shiny parts, otherwise the birds will be scared. In addition, decorative elements should not create obstacles to feed collection.

The use of paint will not only change the color of the structure, but also protect the material from the negative influence of atmospheric factors. Coloring can be monochromatic or multi-colored. In this case, you can use various drawings. It is better if their theme is intertwined with winter motifs. You can find many interesting stencils on sale that will simplify the decorating process.

Bird feeder can be decorated with drawings

You can get an interesting design if you decorate a wooden structure in the form of a beehive or a miniature mill. This work is very meticulous, but if you try, you can achieve complete resemblance to real buildings. Decoration in the form of small branches will add natural charm to the design. You can hang a beautiful pine cone or an edible garland at the entrance, the main thing is that it does not block access to food.

Old dishes can be used for decoration, for example, a saucer with a cup or a teapot. To do this, 4 holes are drilled in the saucer and a rope is pulled through them. After this, the cup is glued to the saucer. This design can be hung in any corner of the yard. The design of the feeders looks original with carvings, bright paintings, pieces of leather and appliqués. By creating several designs in the same style, you can get a beautiful composition that will highlight the exterior of the yard.

An easy way to decorate your feeder is to paint it in different colors.

By spending a little time building a bird feeder with your own hands, you can not only provide the feathered inhabitants of your garden with a tasty snack, but also get a worthy decoration for your yard.

A bird feeder performs several functions at once. Firstly, it is a place to save birds from starvation. Secondly, the feeder decorates the exterior of gardens, parks or simply streets. Thirdly, making a feeder is quite an entertaining process that unites parents and children and teaches the younger generation norms of behavior and human qualities. Therefore, whenever possible, we recommend building feeders, and we will learn how to do this further.

How to make a bird feeder with your own hands

We invite you to familiarize yourself with the main variations of bird feeders, which are most often used to feed them in the winter.

The first and simplest option is to make a roofless forest canteen. It has a flat shape with sides that prevent feed from spilling out. Such a bird canteen is good because it attracts birds, as they do not like enclosed areas. The disadvantage of the feeder is that the food quickly gets wet and spoils under atmospheric influences, and the wind easily overturns such a feeder. To construct this variation of the feeder, one piece of plywood and bars that serve as a frame are enough. The feeder is fixed using a regular rope; in order for the feeder to attract birds, paint it in a bright shade.

A DIY bird feeder made of wood with a roof is a more sustainable option. Four support posts are installed on a regular base, and the roof of the feeder is fixed on them. The top part for the roof should be slightly larger than the bottom to protect the feed from rain and snow. This version of the feeder is also simple and does not require special experience in working with wood. Among the disadvantages of this design, we note that snow accumulates on the flat roof, the feeder becomes heavy in weight, and can fall from the tree. Therefore, it is recommended to periodically clean such a feeder from snow or install a pitched roof.

If you have sunflowers or large berries at home that birds can eat, it is enough to treat the birds with them. A variation in the production of rowan beads or beads from cones is possible. You can build such a feeder from scrap materials. For example, you can put treats in a regular net, in which tangerines or oranges are sold. You need to hang such a gift on a regular rope. Another method is to add wheat or another grain delicacy to unsalted melted lard; after hardening, you need to make a small ball from this mixture, which is placed in any place accessible to the birds. The congealed fat holds the grain, which is gradually eaten by the birds.

To protect the food located in the tangerine net, you can additionally build a roof. This way, the food will not be exposed to moisture and snow. Periodically, such a feeder needs to be filled with new food. It is possible to supplement the main feeder with additional mesh feeders containing a variety of delicacies. These feeders will be an excellent place for small birds to feed.

If you have coconut shells at home, you can also use them to build a small feeder. It will be a natural addition to any tree and will not stand out particularly against its background. It is necessary to cut two round holes in the shell. We also recommend placing grain mixed with melted fat inside the feeder. This variation of the feeder has an unusual and original design. If you have a steel mesh with a small cross-section of cells at home, you can also build a feeder from it. Select the diameter of the feeder individually; try not to make it too large, as too much feed will make the structure heavier. Make a protective cover on such a feeder to prevent food spoilage.

There are many ideas for DIY bird feeders, all you have to do is get creative and get the necessary materials. A feeder can even be built from cutting a branch. It is enough to connect several of these parts together to form the bottom of the feeder. The roof is made in the same way.

Some craftsmen make feeders from ordinary glass jars. They set them at a certain angle and pour food inside. You can paint such a feeder using special paints for glass surfaces. In the same way, you can make a feeder from the old part. It is better to put gelatinized food in it, previously poured with melted gelatin. In the same way, you can make attractive bird feeder decorations. For example, a solution of gelatin and various seeds is poured into a silicone mold; after hardening, it is possible to obtain beautiful shapes: heart-shaped, star-shaped, semicircular, etc.

Beautiful DIY bird feeder

We offer a variation of creating a cereal canteen for birds with your own hands. For this product, it is enough to use food, while the feeder perfectly complements the exterior of the garden and becomes its decoration. When performing the workflow, you will need the following accessories:

• a variety of small-sized food, most often grains or cereals are used;
• eggs;
• oatmeal;
• flour;
• gelatin composition;
• pencil;
• thick cardboard base;
• scissors and thread.

Using a pencil and cardboard, come up with a shape for the future product. It is possible to make a bird canteen in the shape of a star, polyhedron, oval, circle or heart. Using scissors, cut out the previously prepared drawing.

Prepare materials that act as bird food. It is possible to use various grains or bread crumbs. Using a needle, attach a thread to the future sketch, which will later secure the feeder to the trees. In order to firmly hold the grains on the feeder, it is necessary to connect them with a natural adhesive composition.

To prepare it, combine the ingredients in the form:

• two tablespoons of oatmeal, ground into flour;
• one egg;
• one teaspoon of honey;
• a few spoons of flour.

After combining all the components, leave them for half an hour and only after this time, combine them with the previously prepared food.

First, the base of the workpiece is coated with adhesive. In a separate container, all the ingredients for the food are combined with glue. Roll the workpiece in the resulting mixture on both sides. To make the feeders harden faster, place them in the refrigerator for 2 hours.

In the absence of any of the ingredients of the adhesive composition. You can prepare natural glue in another way. To do this, just take one pack of gelatin and soak it in warm water, according to the instructions on the package. Small grain products are combined with the solution and placed in a refrigerator to harden.

This composition can be placed in an old cup or glass; they are also fixed to trees using a rope. This bird canteen is quite easy to make, but at the same time it is an excellent place to feed birds in the winter.

We also suggest that when performing the work process, prepare materials in the form of:

• three flat-shaped boxes of sweets;
• glue;
• tape;
• ropes.

In order to build this feeder, it is enough to connect two candy boxes together with an adhesive solution. At the same time, they should form a roof. The third box is used as the bottom of the feeder. This variation of the feeder is quite easy to make, but at the same time it is an excellent place to feed birds. To protect the cardboard from moisture, the feeder is covered with tape on all sides. In order to fix the feeder on the tree, an additional rope is attached to it. You can decorate the feeder with colored paper in accordance with the chosen design. The only drawback of this feeder is its light weight. It is unstable and does not hold weight well.

Make a bird feeder with your own hands photo:

We offer another easy option for creating a bird canteen. To do this, you need to use a box from any drink. The upper part of the box is fixed to the tree with a cord, and a hole is cut out on the lower part for feeding and eating food. It is recommended to additionally seal the box with tape to avoid its destruction under the influence of water.

DIY bird feeder - original ideas

There are many creative ideas for creating bird canteens. Most often, these exterior elements are made of wood or plastic. We invite you to familiarize yourself with the variation in the construction of a PVC feeder.

When executing the workflow, you will need to have:

• scissors or knife;
• plastic tank with a volume of five liters;
• wire.

In addition, you should prepare food for birds, which will be located in the forest dining room. Using a utility knife or scissors, cut a circular hole in the bottom of the container. The diameter of the opening should be such that a bird can easily fly into it. It is possible to construct several windows at once through which feed will be supplied. The upper part of the container is wrapped with wire and installed on a branch. To weight the finished product, use plywood or similar material that is placed at the bottom. This bird canteen has a roof, so the birds' food will not be wet. In addition, the presence of large diameter holes is the key to ensuring that there will always be a lot of birds in your feeder.

It is possible to design a do-it-yourself bird feeder using PVC bottles. When working on a dining room for birds, you will need to prepare the following materials:

• PVC bottles;
• wires;
• two spoons made of wood.

Using a knife or scissors, make an opening in the container so that a wooden spoon can be inserted through it. 5 cm higher, make another identical hole. Set the spoons and pour food into the bottle. On one side of the spoon, which is adjacent to the bottle with a wide edge, build a hole of a larger diameter. Thus, as the birds eat it, food will spill out of the bottle. The upper part of the container is fixed to the tree most often using wire or rope.

DIY bird feeders photo:

An easier variation of making a bird canteen is to cut out a small door in a PVC bottle. In order to avoid injury to birds as they enter the feeder, all edges of the opening are sealed with electrical tape. Food is poured directly into the container.

Original DIY bird feeder

In the process of creating a wooden forest canteen for birds, you need to stock up on tools in the form of:

• wood or plywood;
• hammer with nails;
• timber;
• screwdriver;
• compositions to protect wood from high humidity.

Using plywood and a board, use a screwdriver to cut out the base for the feeder. The second part should be the same shape, only slightly larger. Thus, it will protect the feeder from moisture. Saw the timber into several parts, from which you need to make sides for the feeder.

To fix the beam, use fasteners and a hammer. A wire or cord should be fixed to the roof, which will hold the roof on the branches. To connect the roof and the bottom of the forest canteen, additional supports are used, installed in the corners, or two in the center. Open the feeder with an antiseptic, which prevents its destruction under atmospheric influence; it is additionally recommended to varnish the feeder.

Please note that it is strictly forbidden to feed birds fresh bread, rye breads and flours, citrus fruits, salty foods, toasted seeds, and oatmeal. These products will not bring any benefit to the birds, but will only harm them.

Various types of grain, wheat, nuts, fruits, dried foods, lard, rowan and viburnum, etc. are used as food for birds. A beautiful homemade bird feeder will decorate any interior; children will enjoy watching the birds eat food and rejoice in the fact that they are taken care of.

DIY bird feeder video: